<p id="ge2gc"></p>

<td id="ge2gc"></td>
<p id="ge2gc"></p>
  • <td id="ge2gc"></td>
    1. <p id="ge2gc"></p>
    2. 歡迎進入貴州鑫瑞達電子有限公司網站!

      新聞分類

      產品分類

      聯系我們


      貴州鑫瑞達電子有限公司

      聯系人:唐經理

      電  話:18786611981

                  15111999738

                  18227999378

      座  機: 0851-83866606

      郵 箱:2541876608@qq.com

      地  址:貴州省貴陽市白云區沙子哨楓桶壩1號

      網址 :www.guccibagsjpshop.com




      快速調試電子地磅的方法

      您的當前位置: 首 頁 >> 新聞中心 >> 行業新聞

      快速調試電子地磅的方法

      發布日期:2018-01-29 作者: 點擊:

      電子地磅使用的越來越多,但考慮到經濟方面,現在只有很少的廠家會把砝碼拉到現場去調試了,那是不是我們的地磅就不用調試了呢?不是這樣的,電子地磅安裝后,檢查電子地磅的各個部位連接是否完好,電子地磅不應與基礎任何部位接觸,電子地磅與四周護邊鐵間距為10mm—15mm。

      More and more electronic loadometer use, but considering the economy, now only a few manufacturers will pull weights to the scene to debug, that is not what we don't have the loadometer debugging? This is not the case, electronic loadometer after installation, check all parts of electronic loadometer connection is intact, electronic loadometer should not contact any part of the foundation, and around the edge of electronic loadometer iron spacing is 10mm - 15mm.


      調試前,須先打開電源開關預熱15分鐘,并盡量用載重量接近最大秤量的車輛,往返多次通過和在承重臺上剎車停留,用力矩扳手擰緊各稱重傳感器高強度螺栓。都是在工廠里面調好后出去的,那對于這種情況,我們該如何調試呢?下面我們就來講一講:

      Before commissioning, we must first turn on the power switch and heat it for 15 minutes, and try to use the vehicle close to the largest scale with the carrying capacity close to the maximum weight. It will stop for many times to go on the way and stop on the bearing platform, and tighten the high-strength bolts of all weighing sensors with the torque wrench. All of them are adjusted in the factory and then go out. So how do we debug this situation? Now let's say:


      1、電子地磅承重點調試好后,將相當于最大秤量的砝碼均勻地加到電子地磅承重臺上,按照各種稱重顯示器的說明書所介紹的位置和方法,使顯示值與砝碼值一致后,取下砝碼,并確認空秤顯示為“0”即可。最后,將最大秤量分為若干份,其中須包括該秤的最小秤量、最大秤量及允差改變的各個稱量點,要求電子地磅各點的稱量誤差不大于各量點的最大允差要求。

      1, electronic loadometer supporting point after commissioning, will be equivalent to the maximum weighing weight evenly applied to the electronic loadometer bearing platform, location and methods introduced in accordance with the various specifications of weighing display, the display value consistent with weight value, remove the weights, and confirm the empty scale shown as "0". Finally, the largest scale is divided into several parts, each weighing quantity and allowable maximum and minimum weighing scale which shall include the scale difference change, the requirements of electronic loadometer weighing error not greater than the maximum permissible amount of each point requirements.


      2、用數字電壓表依次測量電子地磅各個稱重傳感器的輸出電壓,如存在不一致,可分別調整接線盒中相應兩只精密可調電阻,以減少相互間差異量。但調整量必須注意,兩只可調電阻的旋轉方向要一樣,旋轉量也要一樣,順時針轉動時其電阻減小,輸出電壓變大,顯示值增加,否則反之。直至調整到電子地磅各只稱重傳感器輸出一致。 調試一般可用重量法進行,即將1/10最大秤量的砝碼,依次放至電子地磅承重臺中心位置及各只稱重傳感器上方的承重臺上,并用實差法準確測出各只稱重傳感器輸出的差異量,同時分別調整電子地磅各個承重點稱重傳感器相應的兩只精密可調電阻,減少相互間的差異量,但旋轉方向和旋轉量也一樣。

      2, the digital voltmeter measurement of electronic loadometer weighing all the output voltage of the sensor, such as inconsistent, it can adjust the corresponding two boxes of precision adjustable resistance, to reduce the amount of the difference between. But the adjustment must be noted that the rotation direction of two adjustable resistors should be the same, and the rotation must be the same. When clockwise rotation, the resistance will decrease, the output voltage will increase, and the display value will increase. Otherwise, it will increase otherwise. To adjust to the electronic loadometer weighing sensor output. Debugging method is generally available weight, 1/10 maximum weighing weight, in order to put electronic loadometer bearing center and each bearing platform above the weighing sensor, and accurately measure the weighing sensor output difference with real difference method, at the same time adjust electronic loadometer weighing sensor corresponding each bearing point two precision adjustable resistance, reduce the difference between the amount, but also the same direction of rotation and rotation.


      3、參考衡安稱重軟件電子地磅稱重顯示器使用說明書(專業技術手冊),檢查各種功能鍵的正確性,提高電子地磅的稱量準確度。

      3, the reference value for an electronic loadometer weighing display weighing software instructions (technical manuals), check the correctness of the various function keys, improve electronic loadometer weighing accuracy.


      本文網址:http://www.guccibagsjpshop.com/news/372.html

      關鍵詞:貴陽地磅,貴州地磅,貴州地磅廠

      最近瀏覽:

    3. 在線客服
    4. 聯系電話
      18786611981
    5. 在線留言
    6. 在線咨詢
      歡迎給我們留言
      請在此輸入留言內容,我們會盡快與您聯系。
      姓名
      聯系人
      電話
      座機/手機號碼
      郵箱
      郵箱
      地址
      地址
      两个人的视频全免费观看韩国
      <p id="ge2gc"></p>

      <td id="ge2gc"></td>
      <p id="ge2gc"></p>
    7. <td id="ge2gc"></td>
      1. <p id="ge2gc"></p>